RANGE OF SERVICES

MECHANICAL AND ELECTRICAL WORKS

GENERAL BUILDING WORKS

INTEGRATED CLEAN ROOM SYSTEM

Sub-Station Design And Finished

Link Main Unit Cubicle

Cubicles are set of electrical equipment Installed in substation distribution serving as driver, breaker, control and connecting power distribution voltage. Ordinary cubicles substation distribution or installed on connecting stations.

Transformer

Broadly speaking, the function of a transformer is to distribute electrical energy to the low voltage and high voltage to, the distribution of this takes place in the same frequency. This function is also known also as the term step-up and step-down.

Main Switch Board

Main switch Board is an arrangement of electrical / electrical components are assembled or arranged in such a way so that the control board in an interrelated and form functions according to the needs of those wanting the power consumption. Main Switch Board connects the generator and the electrical load (motor, blower, lights etc.)

Distribution Board Panel / Sub Board Panel

To drain the electrical energy from the step-down substation (GI Step down) to load power (consumption) must pass through power panels and electrical distribution panel. Power panel is the place to deliver and distribute electrical energy from an electrical substation step-down to the distribution panels. While the definition of electrical distribution panel is a channel and distribute electrical energy from the power panel to load (consumption) for power installations as well as for the installation of lighting.

Capacitor Bank

Capacitor bank is one of the electronic components are constructed from a plurality of capacitors, where the function and purpose is to repair the cos phi or also called power factor. To install this component is always the same way ie in parallel.

Installation Equipment & Accessories Electrical Work


Cable Support System


Cable Ladder, Cable Tray & Trunking is a cable support system which can be guard cable with sturdy structure for any installation condition in whole project, such as oil, gas refinery, electrical generator system, factory, high-rise building, etc.

Explosion Proof Equipment


Lighting Installation


Lightning Protection System

A Lightning Protection System (LPS) is designed to protect a structure or building and contents from damage caused by the intensely high voltage currents of a lightning strike (often exceeding a 1,000,000,000 Volt Amps). Lightning protection systems act like a faraday Cage for buildings.

Protecting the building and its contents from external electric fields by migrating that energy around the cage instead of through its contents. A lightning protection system offers a lightning strike a low resistance path to ground where the enormous energy is then safely dispersed.

A typical lightning protection system includes lightning rods, metal conductors and ground electrodes designed to offer a low resistance path to ground and to take any high voltage currents from a lightning strike away from the structure of the building.

Dust Collector

A dust collector is a system used to enhance the quality of air released from industrial and commercial processes by collecting dust and other impurities from air or gas. Designed to handle high-volume dust loads, a dust collector system consists of a blower, dust filter, a filter-cleaning system, and a dust receptacle or dust removal system. It is distinguished from air cleaners, which use disposable filters to remove dust.

Cooling Tower C/W Piping System

A cooling tower is a heat rejection device that rejects waste heat to the atmosphere through the cooling of a water stream to a lower temperature. Cooling towers may either use the evaporation of water to remove process heat and cool the working fluid to near the wet-bulb air temperature or, in the case of closed circuit dry cooling towers, rely solely on air to cool the working fluid to near the dry-bulb air temperature.

Air Compressor System

An air compressor is a device that converts power (using an electric motor, diesel or gasoline engine, etc.) into potential energy stored in pressurized air (i.e., compressed air). By one of several methods, an air compressor forces more and more air into a storage tank, increasing the pressure. When tank pressure reaches its upper limit the air compressor shuts off. The compressed air, then, is held in the tank until called into use. The energy contained in the compressed air can be used for a variety of applications, utilizing the kinetic energy of the air as it is released and the tank depressurizes. When tank pressure reaches its lower limit, the air compressor turns on again and re-pressurizes the tank.

Water Pump System

Piping and Ducting Installation

Fire Alarm System

A fire alarm system has a number of devices working together to detect and warn people through visual and audio appliances when smoke, fire, carbon monoxide or other emergencies are present. These alarms may be activated automatically from smoke detectors, and heat detectors or may also be activated via manual fire alarm activation devices such as manual call points or pull stations. Alarms can be either motorized bells or wall mountable sounders or horns. They can also be speaker strobes which sound an alarm, followed by a voice evacuation message which warns people inside the building not to use the elevators. Fire alarm sounders can be set to certain frequencies and different tones including low, medium and high, depending on the country and manufacturer of the device. Most fire alarm systems in Europe sound like a siren with alternating frequencies. Fire alarm sounders in the United States and Canada can be either continuous or set to different codes such as Code 3. Fire alarm warning devices can also be set to different volume levels. Smaller buildings may have the alarm set to a lower volume and larger buildings may have alarms set to a higher level.

Mechanical Ventilation

Air conditioning (often referred to as AC, A.C., or A/C) is the process of removing heat from a confined space, thus cooling the air, and removing humidity. Air conditioning can be used in both domestic and commercial environments. This process is used to achieve a more comfortable interior environment, typically for humans or animals; however, air conditioning is also used to cool/dehumidify rooms filled with heat-producing electronic devices, such as computer servers, power amplifiers, and even to display and store artwork.


Explosion Proof Equipment

A cleanroom or clean room is an environment, typically used in manufacturing, including of pharmaceutical products or scientific research, as well as aerospace semiconductor engineering applications with a low level of environmental pollutants such as dust, airborne microbes, aerosol particles, and chemical vapors. More accurately, a cleanroom has a controlled level of contamination that is specified by the number of particles per cubic meter at a specified particle size.

Epoxy Painting

Epoxy paint is supplied in two liquid components -- the epoxy resin and a hardener -- which must be mixed together immediately before application. Once applied, epoxies are tougher and more abrasion-resistant than ordinary house paints. Because of their chemical-resistant properties, epoxy paints are often used in industrial facilities, but they also fill some very practical needs in the home.


Concrete Work

Concrete is a composite material composed of coarse aggregate bonded together with a fluid cement that hardens over time. Most concretes used are lime-based concretes such as Portland cement concrete or concretes made with other hydraulic cements, such as ciment fondu. However, asphalt concrete, which is frequently used for road surfaces, is also a type of concrete, where the cement material is bitumen, and polymer concretes are sometimes used where the cementing material is a polymer.


Infrared Scanning

Infrared electrical inspections find hot spots caused by defects in connections and components. Infrared thermography is used to find areas of excess heat (caused by increased resistance) so that problems can be corrected before a component fails, causing damage to the component, creating safety hazards and productivity loss. Because increased heating is a sign of failure, infrared is the best diagnostic tool available for finding these hot connections in the early stages of degeneration.


Primary & Secondary Injection Testing


Panel Servicing & Maintenance

Servicng Dust Collector

Servicing Cooling Tower


Contact us

Address

  • Factory B2 Lot 4, Panbil Industrial Estate
  • Mukakuning - Batam - Indonesia
  • Telp: (0778) 371023, 371063
  • Fax: (0778) 371135
  • Email: admin@megastarpersada.com